2010 Hiab 422 EP5 HiPro

Outreach  -  Lifting Capacity (Ft-lbs):

10' 2" - 26,460
16' 1" - 17,200
22' 4" - 12,130
28' 10" - 9,040
36' 1" - 7,050
43' 4" - 5,780
50' 6" - 4,940

Remote Control System

Financing Available
Location: Surrey, BC |  Category: Used 

2021 Freightliner 114 SD

Engine: DD-13 470 HP 1650 TORQUE
Transmission: EATON FULLER RTLO-16918B
Front Axle: 20,000 lbs
Rear Axle: 64,000 lbs 
GVWR:  84,000 lbs
RA Ratio: 4.30
Wheelbase: 285"
Accessories: Rail Deck with Rail Racks, TopSeat Drive, AAR Coupler w/ Train Air, Kinshofer 632R Grapple, Moley Magnet

2020 Palfinger Epsilon S260L

OUTREACH - LIFTING CAPACITY (M -KGS):

8 METERS - 2,890 KGS 
5 METERS - 4,640 KGS 
7 METERS - 3,310 KGS 

Max. Lifting Capacity: 16,200 lbs
Max. Outreach: 22.5 feet
Weight Without Rotator/Grab: 5,250 lbs
Slewing Torque: 28,760 ft-lbs
Slewing Angle/Degress: 385
Extension Type: Double
 

2012 Freightliner M2 112

Engine: DETROIT DD13 12.8L 450 HP @ 1800 RPM
Engine KMS: 246,347
Transmission: ALLISON 4500 RDS AUTOMATIC
Steer Axle: 20,000 lbs
Drive Axle: 69,000 lbs 
GVWR:  89,000 lbs
Wheelbase: 285"
21-Foot Custom Deck
Railgear: Diversified 1650
Options: Rail Grapple, Magnet, Top seat drive, AAR Coupler and tool circuit

VIN #: 1FVPC7DV8CHBR3175

Loglift 251S89

OUTREACH - LIFTING CAPACITY (ft -lbs):

13.1 - 12,566
16.4 - 10,141
19.9 - 8,487
23 - 7,275
26.2- 6,393
27.9 - 5,952

Control #: T032
Serial #: 242834

2003 International 4300 SBA 4x2

Engine: DT466 215 HP
Engine KMS: 475,746
Transmission: 7-Speed Manual
Front Axle: 12,000 lbs
Rear Axle: 21,000 lbs 
GVWR:  33,000 lbs
RA Ratio: 4.33
Wheelbase: 236"
VIN #: 1HTMMAAPD3H561721

Deck Truck

2007 Sterling

Engine: MERCEDES
Engine KMS: 127,496

VIN #: 2FZACGCT17AX80988

3 Ton Deck Truck

2004 Peterbilt 357

Engine: 12.0 L
Engine KMS: 311,769

VIN #: 2NPALUOX14M818015

Deck Truck

2011 Freightliner M2 112

Engine: EATON RTO-16908LL
Engine KMS: 265,211
Engine Hours: 10,922
Transmission: RT0-16908LL
Front Axle: 20,000 lbs
Rear Axle: 59,000 lbs 
Wheelbase: 272"
RA Ratio: 4.3

Deck, toolbox, rear lift axle, crane remote control

VIN #: 1FVHC5DV2BDAX3841
Control #: T2855

2014 Hiab 335 K4 HiPro

OUTREACH - LIFTING CAPACITY (ft- lbs):

25' 3" - 8,270
33' 2" - 5,840
41' 4" - 4,410
48' 11"- 3,620
56'9" - 3,040

2006 Sterling LT9500

Engine: CAT C13 385HP
Engine KMS: 395,000
Transmission: Eaton 15-Speed
Front Axle: 20,000 lbs
Rear Axle: 46,000 lbs
Wheelbase: 268"
22-Foot Deck
Fresh MVI

VIN #: 2FZHAZDE26AV48656

2006 Palfinger PW360

OUTREACH - LIFTING CAPACITY (ft- lbs):

19’ - 9,700
25’ - 7,200
35' - 5,320
43' - 4,240

2008 Kenworth T800

Engine: Cummins ISX 435 HP
Engine KMS: 421,000
Engine Hours: 19,000
Transmission: 18-Speed
GVWR: 52,000 lbs
Front Axle: 20,000 lbs
Rear Axle: 40,000 lbs
18-Foot Lumber Deck with Stakes
MVI Inspection Due Nov 2021
NDT Completed July
Front SFO
Two Aluminum Toolboxes
One Exterior Bin

VIN #: 1NKDL40X98R937822

2007 Copma 280 A-8

OUTREACH - LIFTING CAPACITY (ft- lbs):

16’3” - 9,830
22’2” - 6,390
28’5” - 4,540
34’9” - 3,370
41’4” - 2,600
48’5” - 2,050
55’7” - 1,700
63’2” - 1,430
70’8” - 1,260

With Radio Remote Control

Serial #: 26940

2013 Freightliner 114SD

Engine KMS: 247,838
 

VIN #: 1FVPG3DV9DHFG9098
13-145

2012 Hiab 335 K4 CLX

Outreach -  Lifting Capacity (ft- lbs):
25' 3" - 7,500
33' 2" - 5,290
41' 4" - 4,010
48' 11" - 3,260
56' 9" - 2,730

Serial #: 3350757
Includes Remote Control and Drywall Forks

2007 Freightliner 120 SD

Engine: CAT C15 475 HP @ 2100RPM
Engine KMS: 483,523
Transmission: Eaton Fuller
GVWR: 67,000 lbs
Front Axle: 16,000 lbs
Rear Axle: 51,000 lbs

VIN #: 1FVPALAV47DY45397

2007 Hiab 255 K3 CLX

Outreach -  Lifting Capacity (ft- lbs):
26' 3" - 5 950
33' 6" - 4 370
41' 8" - 3 350
49' 6" - 2 780

Serial #: 2550480
Custom Deck, Drywall Forks, Remote Controls

2006 Scona Triaxle Pup Trailer T13

(2) toolboxes on driver side

2006 Freightliner 120 SD Tri Drive

Engine: CAT C15 475 HP @ 2100RPM
Engine KMS: 496,923
Transmission: Eaton Fuller
GVWR: 72,999 lbs
Front Axle: 18,000 lbs
Rear Axle: 54,999 lbs
RA Ratio: 4.56

VIN #: 1FVPLAV26DU52335

2006 Hiab 255 K3 CLX

Outreach -  Lifting Capacity (ft- lbs):
26' 3" - 5 950
33' 6" - 4 370
41' 8" - 3 350
49' 6" - 2 780

Serial #: 2550099
Custom Deck, Drywall Forks, Remote Controls

2006 Scona Triaxle Pup Trailer T13

(2) toolboxes on driver side
VIN #: 2E9M25D3363003876

2020 Ford F550 Supercab

Engine:6.7L Powerstroke V8 diesel
Transmission: 10 speed automatic
GVWR: 19,500 lbs



Control #: T2535

2020 Palfinger PK 8.501C SLD3

Outreach - Lifting Capacity:
12’6” - 4,332 lbs
18’8” - 2,697 lbs
24’11” - 1,901 lbs
31’6” - 1,415 lbs
38’5” - 1,105 lbs

Serial #: 100500335

DEMATCO OILFIELD PICKER BODY
Full length 5”x3”x.375” HSS mainsills with .375” shear plating at crane mount; 29”W x60”H front vertical cabinets – DS rollered drawer pack and wrench hangers, PS 2 adjustable shelves and wrench hangers, front center storage area with ratchet style shovel loops, Jhooks and removable gate; front bulkhead with lockable chain and boomer storage/recessed chain pans; Binkley flip fifth wheel with steel skid plate, fold down sides and rear gate, underbody tool boxes, rear step, vise and pipe receivers, hitch receiver and 7 pin RV plug, work lights, LED rear lighting, outrigger pad storage and 2 – 20” outrigger pads; painted powder coat black and all lights as per CMVSS; custom tapered aluminum running boards included.

2004 Peterbilt 357

Engine: CAT C12 - 430 HP
Engine KMS: 319,000
Transmission: EATON RTLO16913A
GVWR: 57,500 lbs
Front Axle: 20,000 lbs
Rear Axle: 46,000 lbs

20-Foot Deck, 2 Frame Mounted Toolboxes, Outrigger Pad Holders, Single Front Outriggers, Rear Outriggers, 2 Part Line Block

VIN #: 1NP-ALU0X-3D807521
Control #: N/A

2003 National 1195

OUTREACH - LIFTING CAPACITY (ft- lbs):

28 Ton
95' Boom Length

2020 Isuzu NRR

Engine: 4HK1-T Diesel 5.19L 215hp
Transmission: Aisin A465id 6-speed automatic
GVWR: 19,500 lbs
Front Axle: 7,275 lbs
Rear Axle: 13,660 lbs
Wheelbase: 132.5

Pioneer HR1000 Height adjustable tarp tower.
Spring wind up

Control #: T2745

2020 Palfinger Hooklift T12 L

Container Length: 11 - 14'
Capacity: 12,000 lbs
Jib Height: 36.25"
Dump Angle: 48 Degrees

Serial #: 100518587

2021 Isuzu NRR

Engine: 4HK1-TC Diesel 215 hp
Transmission: Aisin A465id 6 speed Auto
GVWR: 19,500 lbs
Front Axle: 7,275 lbs
Rear Axle: 13,660 lbs
Wheelbase: 132.5

Chassis options include: Cold Weather package,
Suspension Driver seat, heated dual mirrors,
back up alarm, Keyless entry system and PTO
enabled.

VIN #: JALE5W166M7300716

Control #: T2741

2020 Palfinger Hooklift T12 L

Container Length: 11 - 14'
Capacity: 12,000 lbs
Jib Height: 36.25"
Dump Angle: 48 Degrees

Serial #: 100518587

2021 Ford F550 4x4 SD

Engine: 6.7l V8 POWER STROKE DIESEL
Transmission: 10-SPEED AUTOMATIC
GVW: 19,500 lbs
Front Axle: 6,500 lbs
Rear Axle: 14,706 lbs 
RA Ratio: 4.88
Wheelbase: 192”

Features: Compressor 

T2601

2021 Stellar TMAX 1-11 Service Body w/ 6521 Telescopic Crane

11-foot, 35,000 ft/lb rated, 6,000 lb. maximum capacity - 2 Hydraulic Extensions to 21' - PTO Hydraulic with CDT™ equipped proportional radio remote control., Crane Boom Tip Light - Gravity Rotating - Single LED Trilliant Light For Bar Style Flip Sheave., C/W AMERICAN EAGLE 45R HYD ROTARY SCREW COMPRESSOR, 25 GALLON AIR TANK, 35 GALLON HYD RESERVOIR, Heavy Duty Aluminum Drawer set, 35.5"H x 34"W X 18"D, 3-3", 3-5", 1-7" (incl. 2.5" riser), 21 Drawer Steel Bolt Bin w/ Aluminum Pullouts (16 H x 47.25 W x 17.25 D), 1/2" x 50' hose reel with roller guide - exits rear of body, Chain rack - single rack kit for inside compartment or on loadbed wall, Grab handle - mounted to rear side pack and workbench bumper - Easily accessible from ground, Wheel Chock Holder, TMAX Aluminum Tailgate - 12" Tall, painted black, Trailer plug - 7-pin, Vise mounting plate - Receiver workbench mount, Stabilizer, hydraulic out/hydraulic down, Loadbed Cover, Flood light kit (4) for TMAX aluminum body, LED Compartment Light Kit, Back up alarm, CC safety kit consisting of rechargeable 2.5# fire extinguisher and reflector kit, Truck Upfitter Switches Control Package installed For TMAX body with crane and compressor for chassis which is equipped with five or more switches

Financing Available
Location: Surrey, BC | Category: NEW Equipment

2021 Ford F550 F550 4x4 SD XLT

Engine: 7.3L Gas 
Transmission: 10-Speed Automatic
GVWR: 19,500 lbs
Front Axle: 7,000 lbs
Rear Axle: 12,000 lbs
RA Ratio: 4.88
Wheelbase: 192"
 

Control #:  T2668

2020 ETI ETC37IH

Telescopic; Shear Ball; Rotation Bearing; Body Harness with Deceleration Lanyard; Two Operators and Maintenance Manuals
Working Height: 41'9"
Height to Bottom of Bucket: 36'9"
Side Reach: 28'
Fiberglass Inner Boom, Hoses Inside Boom Are Contained in a Cat Trac, Lower Boom w/ Fiberglass Insert for ETC37, Upper Boom Assembly for ETC37IH, Pedestal (41.75)(Standard for ETC37) End Mount Bucket Bracket with 180 Degree Hydraulic Rotator, Turret assembly for ETC37, Manual emergency lowering valve at bucket controls, tart/Stop at basket, 2-Speed Throttle at basket, Palfinger Aerial Body - Galvanneal Steel E-Coat Corrosion Protection 132" Length 96" Width 20" Deep Compartments 56" Load Area Width 40" Side Compartment Height 25" Compartment Height Above Load Area Floor Steel Treadplate Floor Recessed Whale Tail Door Handles - Keyed alike SS1 and CS1 Compartment Size: 33" SS2 and CS2 Compartment Size: 24" SS3 and CS3 Compartment Size: 46" SS4 and CS4 Compartment Size: 29" Full Length Shelf with Rear Access Door in Curb Side Pack, 36" Long Tailshelf Smooth plate entryway steps on curbside with grip strut step underneath. Hand rail on left hand side of entry Through box in tailshelf with a 8" x 17.5" wide opening. Access doors on both side with whale tail latches -keyed alike at the body Receiver tube at the rear, Body Kit and Master Lock

Financing Available
Location: Surrey, BC | Category: NEW Equipment

2021 Ford F550 F550 4x4 SD XLT

Engine: 7.3L Gas 
Transmission: 10-Speed Automatic
GVWR: 19,500 lbs
Front Axle: 7,000 lbs
Rear Axle: 12,000 lbs
RA Ratio: 4.88
Wheelbase: 192"
 

Control #:  T2667 

2020 ETI ETC35SNT

Non-Continuous Rotation
Steel Inner Boom
Steel Lower Boom
Variable Speed Control at the Upper Controls
Upper Controls Mounted on Bucket
Working Height: 40'
Height to Bottom of Bucket: 35'
Side Reach: 27'
Hydraulic Bucket Leveling; Hoses Inside Boom Are Contained in a Cat, Trac Emergency Upper Boom Controlled Descent Valve Start/Stop at basket, 40" Side Compartment Height; 25" Compartment Height Above Load Area Floor, Steel Tread plate Floor, Recessed Whale Tail Door Handles, Wheel chocks (2) with hair pin metal handle. 8Wx10Lx5.5H with 5 inch handle, Cone Holder installed, backup camera system, 5 LB. ABC fire extinguisher mounted in cab if there is no interference. Triangle Warning Kit, Spare fuse; Vertical compartments will have light on door. Horizontal will have light top front center of compartment., Body Clearance Lights - Red/Amber LED Body Reflectors; Backup Lights – LED, Tail Lights - LED (stop/tail/turn) with license/tag light Triple ID Lights – LED, Backup Alarm, Combination pintle hitch with 2" ball, Pintle adapter plate for 2" receiver.: 

Location: Surrey, BC | Category: NEW Equipment

2021 Ford Transit 350 Van

Engine: 3.7L Ti-VCT V6
Transmission: 6-Speed Automatic w/ OD Select
Shift
GVWR: 9,500 lbs
Dual Bucket Seats
Vinyl Front Bucket Seats
Monotone Paint Application
AM/FM Radio
Oxford White
 

Control #:  T2580
 

2021 ETI ETT29SN Aerial Device

Height to Bottom of Bucket: 29ft
Working Height: 34ft
Side Reach: 22 ft 9 inches
Stow Height: 9 ft 6 inches
Rated Bucket Capacity: 350 lbs

Financing Available
Location: Surrey, BC | Category: NEW Equipment

2020 International CV 515

Engine: 6.6 Diesel
Engine KMS: 4,866
Engine Hours: 10
Transmission: Automatic
GVWR: 22,500 lbs
Front Axle: 7,500 lbs
Rear Axle: 15,000 lbs
Wheelbase: 162"
VIN #: 1FD0X5HT3JEC31952
 

Control #:  T2263
VIN #: IHTKTSWM7LH829

2020 Palfinger ETC MH37IH

Working Height: 42'
Height to bottom of the bucket: 37'
Capacity: 1,000 lbs
Bucket capacity: 400 lbs
Side reach: 27'5"Continuous rotation
Fiberglass inner boom
Upper controls mounted on bucket
Variable speed control at the upper controls Hydraulic bucket leveling
Hoses inside boom are contained in a Cat trac Start / Stop at basket
Emergency ower at basket
Hydraulic JIB with winch
60ft of winch line
Serial #: 1119CM716310

Financing Available
Location: Surrey, BC | Category: NEW Equipment

Maeda MC-285C Mini Crawler Crane
Dimensions (Stowed): L 10'11'' x W 2'6'' x H 4'10''

Maximum Capacity:6,210 lbs
Maximum Working Radius:26'9''
Maximum Lifting Height:28.54'
Hook Speed:30.5 ft/min 4 Part/4th Layer
Single Line Speed:122 ft/min 4 Part/4th Layer
Hoist RopeIWRC 6 x Fi(29) 7mm x 158'
Net Weight4,322 - 4,675 lbs

Boom Type:Fully Automatic 5-Section
Boom Length:8'4'' - 28'1''
Boom Speed:19'10'' / 22 Seconds
Boom Hoist (Angle/Speed):0° - 80° / 14 Seconds
Swing (Radius/Speed):360° / 1.0 RPM
Engine:Yanmar 4-Cycle, 2-Cylinder Diesel, 9.92 HP
Remote Control:Cable Remote Control

2022 Freightliner 108SD

Engine: Cummins ISL 370 HP @2200 RPM
Transmission: Allison 3000RDS Automatic
GVWR:  39,000 lbs
Front Axle:  16,000 lbs
Rear Axle: 23,000 lbs
Rear Axle Ratio: 6.14
Wheelbase: 180"

Rear Pintle Hitch (with air)
50 Gallon Fuel Tank

Snow & Ice Package

12'6" HENDERSON MARK E DUMP BODY:
High Lift Gate, LED lights, cab shield with
integral tarp, 36" side height, with walk rail
and fold down ladder, 1/4" AR floor
10' HENDERSON REVERSIBLE SNOW PLOW (RSP):
Quick hitch plow mount, Bumper to frame kit 12" rubber deflector, 36" markers
10' MONASHEE UNDERBODY SCRAPER
11' HENDERSON FSH III SPREADER
Inverted V, Poly spinner, Hold down kit, Top
Screen, 6.2 Yard Capacity
CERTIFIED HYDRAULIC SYSTEM
Freedom 2.2 sander control, 3 stick MDC arm
rest console, frame mounted 30 gallon
hydraulic tank/sealed valve enclosure

2019 Western Star 4900FA

Engine: Detroit Diesel DD13 470HP
KMS: 9,465.8
Transmission: Allison 4500 RDS
GVWR:  55,400 lbs
Front Axle:  20,000 lbs
Rear Axle: 46,000 lbs
Rear Axle Ratio:  4.89
Wheelbase: 244"

VIN#: 5KKHAEDV3KPKP6457

2019 Henderson 16' Black Belt Max Body

Front Plow: 11' Henderson RSP Reversible front plow with quick hitch 10'
Monashee Fixed Angle Scraper
Construction: .201 stainless steel body construction with AR400 sides & floor LAS & Prewet: 292 Gallons liquid tanks for either LAS or Prewet
Tailgate Type: Hydraulic Highlift Tailgate with Pin on Sander Attachment w/ LAS & Prewet Capability
Tarp:  US Electric Tarp System
Controls: Certified Power XDS Centralized Hydraulics with armrest console
Tow Apron: 45Ton pintle hitch

2018 Underground Puller

Standard Features:
8500 lbs Maximum Linepull
0-150 fpm maximum linespeed
8" bullwheels with 5 grooves
Reel capacity of 2300 ft of 7/16" wire rope
Rope payout on demand
Automatic leadscrew levelwind
Swiveling Rear fairlead
Remote emergency stop button
Overload cut-off

This Model UP-85BD Underground cable puller provides infinite speed control and precise tension and distance monitoring. The 8" bullwheels are powered by a hydrostatic drive with a variable displacement axial piston pump and a two speed hydraulic motor.

2005 Moffett M50 Truck-Mounted Forklift 

Hours: 784.6
Engine: KUBOTA DIESEL – 50HP (37.3)kw
Mast Height: 10 Feet
Tire Type (Front): 31.5x13-16.5 (S.S.)
Tire Type (rear): 31x15.5-15 8 PLY(T.G)
Fork Section: 45x4x2"
Capacity @ 24": 600MM LOAD CENTER – 5000/LBS

Serial #: E070438
Control #: U811

2020 Dieci Apollo 26.6 NA Telehandler
161'' L x 72'' W x 78'' H

Engine:Yanmar, 4-Stroke Diesel, 74HP @ 2500RPM
Transmission:Hydrostatic w/ variable displacement pump
Steering Axles:2, with planetary reduction gears
Front Axle:Rigid, self-blocking diff'l (limited slip 45%)
Rear Axle:Oscillating
Gear Pump (lt/1'):80, with capacity @ max speed
Max. Operational Pressure (bar):230
Distributor Control with Joystick:3 in 1

Max. Capacity:5,511 lbs
Max. Lifting Height:18'11''
Max. Horizontal Outreach:10'8''
Outreach at Max. Height:2'2''
Fork Swivelling Angle:129°
Max. Climb Angle:40%
Total Weight Empty:10,582 lbs
Max. Speed:26 km/h

** 2 units available! **

Financing Available
Location: Surrey, BC | Category: NEW Equipment

2018 Genie GTH 3007

Transmission: Hydrostatic
Engine: Kubota
Engine Hours: 225
Max. Capacity: 6,614 lbs
Max. Lifting Height: 22'7"
Max. Forward Reach: 13'1"
Capacity at Max. Height: 5,511 lbs
Capacity at Max. Reach:  2,204 lbs 

2-yard bucket

2018 Boss Railcar Mover MX7

True pressurized and filtered cab 
Integrated HVAC ducting
Independent pivoting rail gear
Increased over-the-rail stability 
Intelligent rail pressure control
Auxiliary rail pressure backup system

Engine: Cummins QSB 6.7L T4f – 300HP @ 2,500 RPM, Comp 260
Transmission: ZF 4WG210, 4F/3R 
Axles: Heavy-duty Meritor 
Tires: Michelin XKA 
Hydraulically Driven Fan;
Maximize cooling
Reversing function for cleaning
 

2018 Shuttlewagon Railcar Mover NVX5025

Options Include: 
Single point lube
Cold weather package
Passenger side mirror 
Heated mirrors
Deadman switch

Hours: 6
Factory Warranty

Drawbar Pull: 38,000 lbs;
Drivetrain: Engine power transmitted through a torque converter and transmission to heavy-duty no-spin differential and planetary axle assemblies;
Engine: Cummins QSB 6.7 U.S EPA Tier 4 final, 260HP @2500 RPM;
Axles: Two-axle tech heavy duty, plantary type
Frame: Heavy-duty deck plate
 

2014 Shuttlewagon Railcar Mover NVX8040

Options Include: 
Single point lube
Cold weather package
Passenger side mirror 
Heated mirrors
Deadman switch
Corrosion package

Hours: 2,873

Drawbar Pull: 60,000 lbs;
Drivetrain: Engine power transmitted through a torque converter and transmission to heavy-duty no-spin differential and planetary axle assemblies;
Engine: Cummins QSL 9.0 U.S EPA Tier 4 final (electronic), 300HP @2200 RPM;
Axles: Two meriter heavy duty, plantary type;
Frame: Heavy-duty 5"x120"x310" deck frame